Breakthrough Diesel Piston Design Removes Barrier to Downsized Engines with Higher Output

Southfield, Michigan, January 25, 2010 … To reduce CO2 emissions and improve fuel economy, vehicle manufacturers are extracting ever increasing power outputs from smaller diesel engines. Federal-Mogul Corporation (NASDAQ:FDML) has developed an innovative aluminium piston design that can withstand the severe mechanical and thermal loads produced by these heavily boosted engines, allowing significant improvements in engine performance and durability.

Called DuraBowl®, Federal-Mogul’s design strengthens the crown of a diesel engine piston by locally re-melting the alloy around the bowl, significantly improving the fatigue strength of the aluminium where it is most needed. The result is an extension of component life to between four and seven times that achieved with a conventional cast piston.

During the last decade, typical performance outputs for automotive diesel engines rose from 50kW/litre (67bhp/litre) to around 70kW/litre (94bhp/litre). According to Rainer Jueckstock, Federal-Mogul senior vice president of Powertrain Energy, the trend is likely to accelerate driven by increasingly pressing legislative targets for CO2 reduction in most major global markets. “Rising specific outputs place higher mechanical and thermal loads on many of the components where Federal-Mogul has considerable expertise,” he said. “The DuraBowl piston process is an example of how we are succeeding in delivering specialised process technologies that help our customers successfully address these challenges across a range of growing market sectors.”

In a diesel engine, combustion takes place in a hollow bowl in the top of the piston, where temperatures can reach over 400 degrees Celsius (750 degrees Fahrenheit) and pressures over 200 Bar (200 x atmospheric pressure). Federal-Mogul says that under these increasingly difficult conditions, the rim of the piston bowl has an increased risk of failure. Following extensive analysis, the company has identified that both thermal and mechanical failures of the piston bowl can be traced to the presence of free primary silicon particles distributed throughout the aluminium matrix. Aluminium expands eight times as much as silicon, creating stresses within the piston as the temperature fluctuates. Furthermore, each time the cylinder fires repeated mechanical loads could initiate fatigue failure from the corners of the silicon particles. Silicon is a necessary constituent of the aluminium alloy, offering favourable properties such as low expansion and good castability, so it currently cannot be eliminated.

The only potential solution to this problem, until now, has been fiber-reinforced pistons. “Fiber-reinforced pistons increase manufacturing complexity as the molten alloy has to infiltrate the fibres during casting,” said Frank Doernenburg, Federal-Mogul director of technology, pistons and pins. “Furthermore, there is not yet a reliable, non-destructive way to test the integrity of the finished part whereas, with our DuraBowl process, we can do an Eddy Current test to ensure the quality.”

Federal-Mogul’s solution is to pre-machine the cast piston and then re-melt the alloy around the rim of the bowl. The re-melted alloy cools a thousand times faster than it did when originally cast, which leads to much smaller silicon particles; only one tenth of the previous size. Metallurgists refer to this as refinement of the microstructure; a technique known to increase the strength and durability of metal alloys.

“The strength and efficiency of our solution is that the process is physically simple,” said Doernenburg. “The sophistication is in the control of key parameters, which ensure consistent quality. The result is a technically advanced, high-performing and very cost-competitive product when compared with both fibre-reinforced and steel pistons.”

The technological and cost benefits have been validated during extensive engine testing, both by Federal-Mogul and its customers. Doernenburg concluded, “The re-melting process certainly increases piston life and performance substantially, making a significant contribution to improving fuel efficiency and reducing CO2. A conservative estimate would be a fourfold improvement in the life of any cast piston which suffers from bowl rim failures.” The first application of the DuraBowl process is on a high-performance diesel engine recently launched for a leading global vehicle manufacturer.

About Federal-Mogul
Federal-Mogul Corporation is an innovative and diversified $6.9 billion global supplier of quality products, trusted brands and creative solutions to manufacturers of automotive, light commercial, heavy-duty and off-highway vehicles, as well as to the power generation, aerospace, marine, rail and industrial sectors. It is recognised as a premier global innovator in the areas of powertrain, sealing, safety and protection and a leading source of advanced technologies that help increase vehicle performance, improve fuel efficiency and reduce engine emissions for a cleaner world. Federal-Mogul employs nearly 39,000 people located in 36 countries. More information can be found at www.federalmogul.com.

Author: admin

Share This Post On